Who is USG Boral
ACOUSTIC PANELS & CEILING TILES
ACOUSTIC SUSPENSION SYSTEM
For higher end design projects, our complement of specialty ceilings options will help even your most complex designs become a reality.
SHEETROCK® Paper Joint Tape is a high tensile strength paper tape to deliver strong, reliable wall joints that resist cracking, stretching, wrinkling and tearing under tools. Suitable for use with our extensive range of joint compounds to reinforce joints.
Choose the best lightweight building materials, high NRC tiles and our quiet wall and impact wall system to give you the best performance for Cineplex and Games Hall.
New Built Residential
Repair, Maintainance, Improvement
USG BORAL EASYFINISH™
For Architects / Designers
We believe we can change the way buildings are designed, built and occupied by delivering innovations that help you work smarter, do more and build better.
For Builders / Installers
Proudly Supporting those who Build, every step of the way.
Our plastering products, tools & accessories are designed for the home renovator/builder making minor alterations or repairs to plasterboard walls & ceilings.
News & Promotions – USG Boral
LANGUAGE / COUNTRY
LANGUAGE / COUNTRY
Looking for product documents?
Try our Document Finder
Considerations on achieving an ideal Plasterboard surface finish
There is little doubt that most customers have an expectation of a perfectly flat, blemishfree plasterboard surface finish. In practice, however, such finish is impossible to achieve and all that can be realistically expected is the perception of flatness.
Experience shows that satisfaction with plasterboard surfaces improves considerably when the following requirements have been met:
It should be emphasized that even if plasterboard installation has been carried out strictly in accordance with AS 2589, surface finish expectations may not be met unless the other requirements listed above have also been satisfied.
A major cause of dissatisfaction with plasterboard surfaces is, in fact, unfavourable lighting from internal or external sources.
Building Design & External Lighting
There are many factors in modern building design that influence the overall appearance of walls and ceilings. Many of today's homes have large open living areas with unbroken ceilings across adjoining rooms and, importantly, large windows and skylights. While providing the desired modern and spacious look, these features often create lighting conditions detrimental to the appearance of wall and ceiling surfaces.
It is important that surface finish expectations are based on what can be realistically achieved given the design features of the project, particularly when some design features are likely to magnify any minor surface irregularities.
When considering the effects of building orientation and window size and positioning on appearance of wall and ceiling surfaces, one should be aware of the effects of external light at different times of the day (see demonstration above).
Glancing light is the light that shines directly across the surface of a wall or ceiling. When architects, builders and home owners are considering what standard of finish is desired for plasterboard walls and ceilings, it is important to understand how the overall appearance is likely to be affected by glancing light.
Glancing light magnifies surface irregularities and can spoil the look of the highest quality surface finish.
As plasterboard linings are constructed on site using materials of two different surface textures and porosity (paper faced plasterboard and jointing compound), they cannot be expected to have a perfect, blemish-free surface. Because glancing light creates shadows from even minute undulations, it will highlight surface irregularities that would not normally be visible under a more diffuse light.
A wall or ceiling surface may be subjected to many different lighting conditions. Lighting direction and intensity changes constantly throughout the day and at night, depending on the position of windows and lighting, and the sun's reflections from adjacent buildings, water surfaces etc.
Critical instances of glancing light can occur when single unshaded light source is fixed directly to the ceiling or wall, but also in rooms with windows up to ceiling height or windows adjacent to walls (above).
A particularly severe glancing light problem occurs when a surface-mounted fluorescent batten light fitting is placed parallel with the plastering joints. Resultant high intensity white light falling at a shallow angle will magnify any surface irregularities (right).
Eliminating Glancing Light
A number of measures can be considered in order to eliminate glancing light effect on interior surfaces:
Incorrectly positioning a spotlight to highlight an object can also create glancing light effect emphasising surface irregularities on walls and ceilings. Feature or spot lights should light only the featured object (right).
Lighting is one of the most important elements in building design and can add that special finishing touch. One must be aware of the effects of glancing light when considering lighting types and positioning.
Modern lighting solutions can help to balance illumination and shadow and to achieve a better outcome in a new home or commercial project.
Although the selection of light fittings is usually governed by taste and budget, it is wise to consider lighting effect on internal surfaces even before construction is commenced.
Large living areas, which are a feature of modern open plan designs, are the most severely affected by glancing light. Consideration should be given to illuminating such areas with general diffused light using downlights or spotlights, in combination with local accent lighting such as floor lamps, table lamps etc.
Fluorescent or unshaded ceiling lights installed in kitchen areas that form part of a large open living area will, in some cases, create unfavourable effects on the other ceilings by highlighting variations in the finished surface.
In two storey dwellings, some downlights may not fit within the floor cavity. This needs to be taken into account at design stage.
Gloss/Sheen Paint Finishes
Gloss and even semi-gloss paints will accentuate surface variations regardless of the direction of lighting or the viewing angle. Flat paints, on the other hand, reflect light in a diffused form and thus mask surface variations.
As plasterboard's paper surface has a different surface texture from hand applied jointing materials, this difference in texture can be accentuated by gloss paints.
Where gloss or impervious sheen paint finishes are desirable or mandatory for functional reasons (eg in kitchens, bathrooms and commercial food preparation areas), some loss of appearance can be expected, even when the work has been carried out to the highest level of workmanship.
For the reasons outlined, a full gloss paint finish is not recommended on plasterboard walls or ceilings. Where gloss or semi-gloss paints are to be used, the highest level of plasterboard finish as stipulated by AS/NZS 2589:2007 'Gypsum linings - Application and Finishing' is recommended (Level 5 finish; see Levels of Finish).
Careful consideration must also be given to:
The quality of a painted finish can be improved if adequate steps have been taken in preparation of plasterboard surfaces prior to painting:
All surfaces should be clean and dust free prior to painting
Any major defects visible after the first (sealer undercoat) coat of paint should be referred to the plasterboard contractor before proceeding with the second and final coats. Minor blemishes are normally attended to by the painter.
Application (Level 4 Finish)
For the best results, Boral Plasterboard recommends roller paint application and the use of a suitable sealer undercoat over the entire plasterboard surface in order to equalise porosity and texture of the jointing material and plasterboard paper face.
Sealer undercoat should be lightly sanded before applying the second paint coat.
As spray painting does not impart a textured surface and does not equalise the porosity of what is essentially two different materials, it tends to emphasise the paper nap and accentuate joint locations.
If the spray painting method is to be used, it is recommended that all paint coats are backrolled and allowed to dry thoroughly prior to application of subsequent coats.
Backrolling must be carried out over wet paint to create a textured background for subsequent paint coats. Choice of colours is also important, as some darker colours tend to highlight surface variations. Light colours give better results, and white is recommended for the ceilings (refer to AS/NZS 2311:2009 'Guide to the Painting of Buildings').
Levels of Finish
The term 'level of finish' applies to plasterboard linings prior to decoration.
AS/NZS 2589:2007 'Gypsum linings - Application and Finishing' defines three levels of finish: Levels 3, 4 and 5. Level 4 is the default level of finish for plasterboard surfaces, unless specified otherwise.
It is essential that the level of finish is determined at the design stage since each level of finish has specific requirements for substrate tolerances and plasterboard installation, jointing and finishing. The desired level of finish may not be achieved unless all of these requirements are met through various stages of construction. For a full description of levels of finish refer AS 2589.
This level of finish is used in areas that do not require decoration or where finish is not important (for example, above ceilings or inside service shafts and the like).
All joints and interior angles must have tape embedded in the joint compound and one separate coat of joint compound applied over all joints and fastener heads
This is the default and generally accepted level of plasterboard finish.
All joints and interior angles must have tape embedded in the jointing compound and a minimum of two separate coats of joint compound applied over all joints, angles fastener heads and accessories.
If Level 4 surface is to be exposed to critical lighting, it should be covered with textured finishes or wall coverings. Smooth textured finishes and flat/matt or low sheen paints can be used when Level 4 finish is illuminated by non-critical lighting. Flat paints in this situation tend to conceal joints.
Weight, texture and sheen level of wall coverings/finishes should be carefully evaluated and joints should be adequately concealed if wall-covering material is lightweight, glossy or lightly patterned.
Level 5 finish should be used where gloss or semi-gloss paints are specified or where flat or low sheen paints will be exposed to critical lighting conditions. Level 5 finish is characterized by a parity of surface texture and porosity.
All joints and interior angles must have tape embedded in the jointing compound and a minimum of two separate coats of jointing compound applied over all joints, angles, fastener heads and accessories.
The work is finished with proprietary surface preparations or skim coating to remove differential surface textures and porosity. A suitable paint or plaster material is sprayed, rolled or trowelled over the defined area. The surface texture must be random and monolithic, concealing joints and fixing points.
Most common examples of unfavourable lighting